Track chains

Track chains consist of chain link segments, which are connected to each other by bushes and pins. The drive sprockets drive the track chains, which in turn advance the machine in the desired direction of travel. The chain tension must be sufficiently high to ensure that the teeth of the drive sprocket securely engage in the track chain. Depending on the loading on the track chains by the operating weight of the machine and its maximum possible advance speed, WIRTGEN GROUP machines use not only dry, but also lubricated track chains.

In the case of lubricated chains, there is a lubricant between the bushes and pins that minimises friction between these components and, depending on the application, lengthens the service life of the track chains. The chain tension is created by a tensioning system. The necessary tension is provided and maintained either by a spring-grease tensioning cylinder or a hydraulic tensioning cylinder.

The dimensions and materials of all genuine WIRTGEN GROUP track chains are precisely matched to the drive sprockets, track pads and track rollers. They effortlessly withstand even the toughest continuous stresses in everyday use.

Wear on track chains

In order to keep wear on track chains to a minimum, it is essential to ensure that they are always correctly tensioned.

  • If the tension created by the tensioning cylinder via the drive sprocket and idler is too high, the necessary play between bushes and pins will be too small, and will cause increased wear.
  • On the other hand, insufficient track chain tension leads to an undulating motion of the chain links between the drive sprocket and the idler. As a result of this, the chain link flanks rub on the side surfaces of the track rollers and the drive sprocket, This can lead to track chains being thrown.

The chain tension should therefore be regularly checked, especially in the case of grease tensioned crawler units.

Track chains stretch over time. The degree of stretch can be checked with the wear dimensions shown in the table. The track chain is also precisely matched to the tooth profile of the drive sprocket This profile changes in the course of the operating time. If either the drive sprocket or track chain need to be replaced, always replace both at the same time.

Chips on chain links can lead to a broken chain.

Mounting direction of the track chain.

Stresses under load lead to wearing of the chain link height and stretching.

WEAR DIMENSIONS OF WIRTGEN TRACK CHAINS
Machine model Crawler size Chain type Wear dimension (mm)
0% 20% 40% 60% 80% 100%
WIRTGEN Track chains – wear dimension A
W 1000 F, W 1200 F, W 1300 F,
W 100 F(i), W 120 F(i), W 130 F(i),
W 100 CF(i), W 120 CF(i), W 130 CF(i),
W 150(i), W 150 CF(i), W 1500,
W 1900, W 195, W 200(i), W 200 H(i)
W1 lubricated 73 71.8 70.6 69.4 68.2 67
W 2000, W 205, W 215,
W 210(i), W 210 XP
W3 lubricated 76.8 75.6 74.4 73.2 72 70.8
W 2100 (up to ser. no. 0147) W4 dry 96 94.3 92.6 90.9 89.2 87.5
W 2100 (form ser. no. 0148), W 220(i) 96 94.4 92.8 91.2 89.6 88
W 2200, W 250(i) W5 dry 103.9 102.1 100.3 98.5 96.7 94.9
WIRTGEN Track chains – wear dimension L

W 1000 F, W 1200 F, W 1300 F,
W 100 F(i), W 120 F(i), W 130 F(i),
W 100 CF(i), W 120 CF(i), W 130 CF(i),
W 150(i), W 150 CF(i), W 1500,
W 1900, W 195, W 200(i), W 200 H(i)
W1 lubricated 560 562.4 564.8 567.2 569.6 572
W 2000, W 205, W 215,
W 210(i), W 210 XP
W3 lubricated 622.4 626.3 630.2 634.2 638.1 642
W 2100 (up to ser. no. 0147) W4 dry 684.2 687.8 691.4 695 698.6 702.2
W 2100 (from ser. no. 0148), W 220(i) 686.8 689.2 691.6 694 696.4 698.8
W 2200, W 250(i) W5 dry 701.6 705.2 708.9 712.5 716.2 719.8
Values may vary slightly due to manufacturing tolerances.

The wear dimension ‘L’ is determined by measuring the length of exactly four chain links from the centre of the first pin to the centre of the fourth pin (simplified illustration).

WIRTGEN tracked undercarriages

Order and buy genuine parts for tracked undercarriages from WIRTGEN online.

> Undercarriage and track unit components from WIRTGEN
Back to the Parts Guide
To the Parts Guide