In terms of tensile strength, abrasion resistance, elongation at break and tear resistance, genuine VÖGELE track pads achieve significantly higher performance ratings than their third party counterparts.
Rubber track pads must be replaced when the wear limit of the coating is reached. Replacement should take place before the bars of the steel base plate become visible. The coefficients of friction (the traction) of steel on asphalt are significantly worse than those of polyurethane or rubber. This has a direct influence on the possible feed speed and, consequently, on the machine productivity. At the same time these coatings minimise damage to the ground and prevent possible payment of damages to the customer by service providers or owners of the construction machines. After all, roads or ground that were in good condition but were damaged due to worn track pads must, in general, be repaired or remade.
Machine type: | Wear dimension A (mm) | ||||||
---|---|---|---|---|---|---|---|
0% | 20% | 40% | 60% | 80% | 100% | ||
SUPER 700, SUPER 800 | 45 | 41 | 37 | 33 | 29 | 25 | |
SUPER 700-3(i), SUPER 800-3(i) | |||||||
SUPER 1100-2, SUPER 1300-2, SUPER 1100-3(i), SUPER 1300-3(i) | 52 | 47 | 42 | 37 | 32 | 27 | |
SUPER 1600-1, SUPER 1800-1, SUPER 1600-2, SUPER 1800-2, SUPER 1600-3(i), SUPER 1800-3(i), MT 3000-2(i), MT 3000-3(i) SUPER 1900-2, SUPER 2100-2, SUPER 1900-3(i), SUPER 2100-3(i) | 52 | 47 | 42 | 37 | 32 | 27 | |
SUPER 3000-2 | 57 | 52 | 47 | 42 | 37 | 32 | |
SUPER 3000-3 | 45 | 41 | 37 | 33 | 29 | 25 |
As with all other nut and bolt connections, the track pad bolts must also be tightened with sufficiently high torque. The following table provides the correct tightening torque values for various VÖGELE machines.
Machine type | Dimensions (mm) | Tightening torque | ||
---|---|---|---|---|
VÖGELE bolts for rubber track pads | Ma (Nm) | Ma (ft-lb) | ||
SUPER 700, SUPER 800 | M 10 x 1 | 90 +/- 5 | 66 +/- 4 | |
SUPER 700-3(i), SUPER 800-3(i) | ||||
SUPER 1100-2, SUPER 1300-2, SUPER 1100-3(i), SUPER 1300-3(i) | M 12 x 1 | 160 +/- 10 | 118 +/- 7 | |
SUPER 1600-1, SUPER 1800-1, SUPER 1600-2, SUPER 1800-2, SUPER 1600-3(i), SUPER 1800-3(i), MT 3000-2, MT 3000-3(i) | 1/2“ UNF thread | 180 +/- 10 | 133 +/- 7 | |
SUPER 1900-2, SUPER 2100-2, SUPER 1900-3(i), SUPER 2100-3(i) | ||||
SUPER 3000-2 | ||||
SUPER 3000-3 | M14x20 | 230 +/- 10 | 170 +/- 7 | |
1/2“ UNF thread | 180 +/- 10 | 133 +/- 7 |